The vehicle testing line guarantees the insure the safety of the car after the final assembly. Including bumpy road tests, four-wheel aligners, axle cargo tests, speed testers, boscage testers, sideslip tests headlight testers, and so on. Through the control system, once the auto passes all the test equipment, will be compared with the design date, and also acclimated according to the date of different models to achieve the plant conditions. At present, we have a variety of configurations of testing outfits to meet the requirements of different guests. communicate with us to get further information.
Vehicle testing line process
Bumpy road test → four-wheel alignment → speed test → axle load test → brake test → steering test → light → sound level → side slip test → rain test → paint repair → general inspection → cleaning
Vehicle Bumpy Road Test
As long as there are roads, there are bound to be unevenness, undulations, and potholes. Therefore, a car must adapt to the road surface of the ups and downs and uneven, so the vehicle has a suspension system, there are springs, there are shock absorbers. In daily driving, the car is precise because the road will pass through high and low ups and downs, potholes, and uneven roads, so there will be "different cars with different comfort" differences embodied. Some cars drive through uneven roads when the body comes from intense vibration, followed by an obvious rocking swing, we call it "poor comfort", and on the contrary, the car through the uneven road when the vibration is soft, and can quickly make the swaying body to calm down, we call it "good comfort! We call it "good comfort".
Vehicle Four-wheel Alignment
Today's road surfaces are becoming increasingly uneven due to the growing number of speed bumps and potholes, which can lead to problems with your bus vehicle's steering and suspension. Using a four-wheel alignment system, we can check and adjust the center (toe-in and toe-out), caster, front camber, rear camber, and thrust angle.
Vehicle Brake System
The drum brake test rig with axle weight is used to measure the braking force and wheel weight of each axle (left and right wheels) of the inspected vehicle. It is mainly used to test the braking performance of the bus vehicle under the rated load-bearing mass. This equipment is the core part of the motor car safety performance testing and high technical performance requirements of the safety testing equipment.
The main body is welded as a whole, has high strength, no need to fix the main body on the ground with ground bolts, is easy to adjust and install, reduces the floor space, saves investment, can choose the test bench with or without airbag lifting device (airbag lifting device to facilitate the car in and out of the test bench, with automatic stopping device, to prevent the tire from wearing out.
Vehicle Speed Test Bench
A vehicle speedometer tester is used to detect the display value error of the speedometer when the car is traveling. Vehicle speed odometer tester is one of the important equipments for automobile safety performance testing.
The structure is sturdy and durable, easy to debug, with special knurling on the roller surface, high strength, wear resistance, and large friction coefficient, improving the testing efficiency. It is equipped with a safety protection device to protect the wheels from scratching the tester when it is running at high speed.
Vehicle Side Slip Test Bench
The side slip test bench is mainly used to measure the amount of side slip produced by the joint action of the camber angle and front beam angle of the automobile. In the process of driving in a straight line, it utilizes the left and right motion momentum of the side slip plate to measure the size and direction of the wheels and to judge whether the inspected bus vehicle is qualified or not. It is one of the important equipment for automobile safety performance testing. It can also assist the four-wheel aligner to test before measurement, to judge whether the vehicle needs to adjust the four-wheel alignment, which can save the vehicle maintenance time.
Vehicle Light Meter and Sound Level Meter
Automotive Light meters and sound level meters are mainly used for measuring automotive lights and sound system equipment. Laser-assisted light tracking system, counterweights in the positioning bracket allow the optical box to move up and down easily, battery-powered in low-power mode, lightweight and flexible, simple to operate, easy to move and maintain
Vehicle Rain Test Room
The automobile car rain test room is used for automobile whole or parts in different intensities of rain on the product seepage and leakage of water tightness test, test the waterproof performance of automobile products, for product improvement and research and development to provide a reference basis. In real life, when a car driving on the road encounters rain impact, puddles splash water, and other situations, the automotive rain test room in the construction design, simulates the situation of high-intensity rain.
The automobile rain test room in the design, needs to carry out all aspects of the rain test, the strength of the water spray and water spray angle should be suitable, and in line with national standards. In addition consider the water supply system of the automobile rain room, to be able to do not lack of water, recycling water for testing, water filtration and removal of impurities, and recycling water. Automobile rain test room to ensure that the vehicle from the side and top of the car window surface for water spray, all-round water spray test, water spray test, water pressure, and flow should reach the national standard.
Car test line equipment is mainly used for testing and verifying the quality of products in all aspects of the automotive production process, to ensure that the vehicle can meet the established performance standards and safety requirements before leaving the factory. Automotive test line equipment usually contains the following types of equipment and functions:
Vehicle performance testing system: It is used for comprehensive testing of the core performance of the car, such as power, brakes, suspension, emissions, and so on. Simulating the driving environment ensures the vehicle meets road driving requirements.
Four-wheel Positioning Test System: It is used to test and adjust the four-wheel positioning of the vehicle to ensure that the angle and positioning accuracy of the wheels is in the best condition, so as to ensure the stability and safety of the vehicle traveling.
Emission testing system: It is used to measure the composition of the exhaust gas emitted by the vehicle to ensure that the vehicle complies with the national or regional environmental protection emission standards. The system usually contains an exhaust gas analyzer and a testing platform.
Vehicle Speed Testing System: Measure the maximum speed and acceleration performance of the vehicle through the testing platform to verify the dynamic performance of the vehicle at different speeds.
Brake Performance Test System: Through simulating various working conditions, the braking system of the vehicle is tested to ensure that it can work effectively and ensure safety during emergency braking.
Noise and vibration test system: Used to test the noise and vibration generated by the vehicle during operation, to ensure the comfort and low noise requirements of the vehicle.
Electrical System Test Equipment: Used to test the electrical system of the vehicle, including battery, circuit, lights, sensors, etc., to ensure its stability and safety in use.
Rainfall test equipment: simulates different intensities of rainfall environment to test the waterproof performance of the vehicle to ensure that the vehicle will not leak or enter water under different weather conditions.
Lighting testing equipment: used to test the brightness, angle, and beam consistency of the front and rear lights of the vehicle to ensure that the lighting effect of the vehicle traveling at night meets the standard.
Whole Vehicle Inspection Line: Before the car comes off the production line, the whole vehicle inspection line will carry out an all-around inspection of the comprehensive performance of the vehicle to ensure the driving safety, reliability, and comfort of the vehicle.
These test line equipments ensure the quality stability and safety of automotive products and enhance the driving experience of customers through the strict testing of various vehicle performances. Automotive test line equipment is widely used in the production lines of passenger cars, commercial vehicles and special vehicles, providing reliable quality control for automotive manufacturers.
| No |
Product name |
Size |
| 1 |
Bumpy Road Test |
Customizable for different models |
| 2 |
Four-wheel alignment |
Customizable for different models |
| 3 |
Brake System |
Customizable for different models |
| 4 |
Vehicle speed test bench |
Customizable for different models |
| 5 |
Side slip test bench |
Customizable for different models |
| 6 |
Light meter and sound level meter |
Customizable for different models |
China Vehicle Industry Provides One-Stop Vehicle Solutions
Skd Parts Guidance And Supply
We produce all the parts by ourselves, so we can offer you the stamping and auto parts and give you the production process guidance. Just as you want to start building your own bus/car factory, a bus/car needs more than 10,000 parts, you do not have to produce all the parts, many parts we already have ready-made molds and solutions, and we can provide good quality and cheap KD parts.
Technical Guidance And Supply
We have already directed the design for dozens of companies. According to your production plan and local labor cost, we will reasonably suggest some necessary equipment, so you can only spend perfect money and realize your car dream.
One-Stop Shopping Service
We provide a one-stop purchasing system to provide you with electric vehicle solutions. This will be a brand-new, epoch-making product, and you will become the most important electric vehicle manufacturer in your country
We design different automotive installation lines, automotive test lines, automotive welding lines, etc. according to the needs of customers, we will also send our engineers to the site to carry out installation guidance, and we cooperate with customers all over the world, such as Egypt, Russia, Thailand, Laos, Ethiopia, South Korea, Dubai, etc.
We have been very successful in the automotive assembly industry, and we have achieved a great deal, of course, we have achieved quite a lot of certificates, such as a CE certificate, ISO certificate, and IATF certificate, and we will be according to the size of the customer's origin, the needs of the development of the program.
China Vehicle Industry Co., Ltd is a company that provides the whole auto industry chain services, from vehicle manufacturing equipment to vehicle parts, electric drive technology, testing equipment, auto parts, and training services. At the same time, we provide industry solutions to help you build your auto dream. At the same time, we also support charging station technology, which has been the world's current photovoltaic charging technology. Guided by a commitment to excellence, we continuously explore new possibilities and achieve ambitious goals.
We produce all the parts by ourselves, so we can offer you the stamping and auto parts and give you the production process guidance. Just as you want to start building your own bus/car factory, a bus/car needs more than 10,000 parts, you do not have to produce all the parts, many parts we already have ready-made molds and solutions, and we can provide good quality and cheap KD parts.
In response to the opportunities and challenges of the current era, China Vehicle Industry Co., Ltd. specializes in providing customized technology production line designs and targeted solutions for customers across welding, painting, assembly, and testing processes. Our goal is to help our customers realize their automotive dreams and contribute to a better life and society through excellence in automobile production and manufacturing.
Car assembly lines adopt the method of combining an iron frame with an export wooden packaging box to enhance packaging protection for parts susceptible to friction. Apply phosphating electrophoresis anticorrosion treatment to all six vehicle body skeletons and steel components.
){kind=link}